Boat Airdopes 451v2 Wireless Earbuds User Manual Guide

Boat Airdopes 451v2 Wireless Earbuds User Manual : This is new launched by boat. Let’s check the user guide of airdopes 451v2 bluetooth earbuds.

Join Us on Telegram : Click Here

Table of Contents

Boat Airdopes 451v2 Wireless Earbuds User Manual

Package Contents

1N pair of TWS earbuds
1N Charging case
2N Pairs of additional earmuffs
1N Type-c charging cable
1N User manual
1N Warranty card
1N Catalogue
1N FAQ Card
1N GFPS ( google fast pair service) card
1N Read me card

Power On (First time user)

STEP 1:To switch the earbuds on (Smart Power On) simply open the lid of the charging case (when earbuds are inside). Our IWP'” (Insta Wake N’ Pair) Technology enables the earbuds to power on automatically, get connected and enter into the connection mode or

Long touch the CTC on both earbuds for 2 seconds to manually power on the earbuds. The led flashes in blue for 1 second

STEP 2: Both the earbuds will automatically pair with each other. The earbuds will enter into the Connection Mode, indicated by red and blue LED flashes.

Boat Airdopes 451v2 Wireless Earbuds Power On (First time user)

Smart Power Off

STEP 1: After usage, remove both the earbuds from your ears.

STEP 2:Place the earbuds back into the charging case in correct orientation

STEP 3: The earbuds will automatically switch off (and enter into place your commands at ease charging mode)

Manual Power Off:

STEP 1: Long touch the CTC on either earbud for 8 seconds

STEP 2: Once the earbuds get turned off place them back inside the case and close the lid

Connection Mode

STEP 3: Turn on the Bluetooth functionality on your phone/media device and scan

STEP 4: Search for ‘Airdopes 451 v2’ and pair accordingly. Successful pairing is indicated by 3 flashes of blue LED for every one minute and ifthe pairing is unsuccessful/disconnected it again goes back to the pairing mode indicated by red and blue flashes.

Congratulations! Your earbuds are now connected successfully via Bluetooth.

Boat Airdopes 451v2 Wireless Earbuds Connection Mode

Note

Pairing mode lasts for 5 minutes. if the pairing time is miss then you will need to reconnect the ear buds and follow the above mentioned procedure.
You may press the Pairing / Reset Burton present on the case in order to make the earbud5 enter into mode, in case they power off after inactivity.
Subsequent Pairing: Airdopes 45 v2 remembers previously connected devices; once switched on, the earbuds automatically to the previously connected devices.

Factory Reset

Perform the Factory Reset in case you face any difficulty while operating your Airdopes 451 v2

NOTE: Before performing reset, clear “Airdopes 451 v2” from pairing device history by forgetting device.

Step I: Place both the earbuds back inside the charging case in correct orientation

Step 2: Long press the Reset Button on the case for up to I O seconds to do Factory reset, which is indicated by the flashing of white LED three times

Step 3: Shut the lid of the charging case and then re-open it again

Step 4: Once you take the earbuds out from the charging case, they automatically

Step 5: Congratulations! Your Airdopes 451v2 has been Reset.

Boat Airdopes 451v2 Wireless Earbuds Factory Reset

Single Earbud Use

STEP 1: Please note that both the earbuds can be used in mono mode. Use Smart Pcn.ver On for switching on the desired earbud

STEP 2: The selected earbud will automatically enter the connection mode first indicated by a Blue LED flash for 1 second and then by red & blue LED flashes

STEP 3: Turn on Bluetooth on your phone/media device and search for ‘Airdopes 451 v2’ to connect.

Boat Airdopes 451v2 Wireless Earbuds Single Earbud Use

NOTE:

To switch to Stereo mode, simply take out the other earbud from the case. It will automatically power on and pair with the previously selected earbud, hence enabling usage

You cannot skip tracks or return to the previous tracks in Mono mode.

LED Indicators/Functionalities

Charging the Earbuds & LED Indicators

Step l: Please insert the earbuds back inside the charging case in correct orientation.

Step 2: While on charge, once you open the case lid, the red LED stays solid for 2 seconds to indicate charging and then it turns off. Once fully charged the LED stays off even if you open the case lid later again

Step 3: Once the earbuds are fully charged, the charging case automatically switches off to save power.

Note

Before using the ear-buds for the first time, it is recommended to fully charge the ear-buds. Also please keep the lid of the charging case close while charging.
When the earbuds are in low power (below30%), once you open the case lid, the low power is indicated by red LED flashes 3 times and then by a voice prompt at 20% remainder battery.

Charging the Case & LED Indicators

Step: TO charge the case, plug one end Ofthe provided cable into the case and connect the other end to a computer,’ wall adapter/ powerbank, etc. The case LED turns into white during charging and once fully charged all the three LEDs turn into solid white.

Standby State Battery Indication

Status	LED Indicators
Remaining – 33.33%	One LEDs stays solid
Remaining – 66.66%	Two LEDs stays solid
Remaining – 100%	Three LEDs stays solid

During Charging

If the battery is below 33.33% the first LED blinks
If the battery is below 66.66% but above 33.33% the first LED, the first LED stays solid and the 2nd LED blinks
If the battery is below 66.66% the first and second LEDs stay solid and the third LED blinks
If the full charge is full, then all the LEDs stay solid.

Important Notice

When you open the case while the left earbud is inside the case or when you put the left earbud inside the case for charging then the case’s left LED initially blinks for 5 times. When you open the case while the right earbud is inside the case or when you put the right earbud inside the case for charging then the case’s right LED initially blinks for 5 times.

Basic Functions

Voice Assistant: Long touch the CTC on either earbud for 3 seconds to activate the voice assistant
Answer/CaII: Single tap the CTC on either earbud to answer an incoming call
Reject Call: Double tap the CTC on either earbud to reject incoming calls
Hang up Call – Double tap the CTC on either earbud to hang up on going calls
Play/Pause Music: Via the In-Ear Detection feature
Next Track: When playing music, double tap the right CTC to skip to the next song
previous Track: When playing music, double tap the left CTC to return to the previous song
Volume: When playing music. volume can be changed by upward or downward swipe gesture on either CTC.

IN-EAR DETECTION

You can play/pause a song via the in-ear detection feature. Place the earbuds inside the ear to play a song; just take them out to pause one.

Initially the user needs to play music manually via the phone just after connection
After disconnection, or after one or both earbuds timeout, it is necessary to manually open the music player to play
If you take out one earbud, then the music can be restored if you plug it back in within 45 minutes; on the other hand if you take out both earbuds then the response time for the same is 4 minutes
During the process of playing music when both earbuds are plugged in, if one earbud is taken out then the music pauses in both the earbuds even if the other earbud is kept plugged in. If one wants the other earbud to play music, one needs to take out that earbud and plug it again inside the ear.

Common Problem With Solution

Troubleshooting

potential Problem	Solution
If one earbud is not working	perform the factory reset
If earbuds are not connection/scan mode	perform the factory reset
If earbuds disconnect during phone call	Charge the earbuds or perform the factory reset
If there are other exceptions is usage	Place the earbuds back into the charging case and try using them again or perform the factory reset
If the In-ear detection or touch controls don’t seem to respond	After long usage, residual stains and perspiration can affect the in-ear detection area use a clean cloth to wipe those areas softly

Specifications

Bluetooth version	V5.0
Water resistance	IPX7
IWP technology	Yes
In-ear detection	Yes
Dual microphones	Yes (Equipped with ENx technology for environmental noise cancellation)
Music playtime	Up to 5H per charge; up to 20H additional with case
Charging technology	ASAP fast charge
Standby time	100H
Transmission range	10m
Driver size	10mm*2
Bluetooth profiles	HFP/HSP/A2DP/AVRCP
Pairing type	Google fast pair/standard pairing
Supported codec	AAC / SBC
Frequency	20Hz-20kHz
Battery	600mAh (case) 60mAh*2 (earbuds)
Charging time	45Min for earbuds, 2-3H for case
Charging interface	Type C

Source

https://www.boat-lifestyle.com/
Download User Manual – Download
Product Page – Click Here

Read More

Frequently Asked Question

How to factory reset boat Airdopes 451v2 wireless Earbuds?

Perform the Factory Reset in case you face any difficulty while operating your Airdopes 451 v2
NOTE: Before performing reset, clear “Airdopes 451 v2” from pairing device history by forgetting device.
Step I: Place both the earbuds back inside the charging case in correct orientation.
Step 2: Long press the Reset Button on the case for up to I O seconds to do Factory reset, which is indicated by the flashing of white LED three times
Step 3: Shut the lid of the charging case and then re-open it again
Step 4: Once you take the earbuds out from the charging case, they automatically
Step 5: Congratulations! Your Airdopes 451v2 has been Reset.

How to pair my boat Airdopes 451v2 bluetooth Earbuds with android or iphone?

1. To switch the earbuds on (Smart Power On) simply open the lid of the charging case (when earbuds are inside). IWP'” (Insta Wake N’ Pair) Technology enables the earbuds to power on automatically, get connected and enter into the connection mode OR Long touch the CTC on both earbuds for 2 seconds to manually power on the earbuds. The led flashes in blue for 1 second
2. turn on your bluetooth of your iphone or android phone.
3. now the boat 451v2 airdopes will visible in your phone’s bluetooth setting. just tap to connect.