If you are searching for Jaybird BlueBuds X Bluetooth Headphones User Manual then this is the right place for you. Let’s check this.
Jaybird BlueBuds X Bluetooth Headphones User Manual
SPECIFICATIONS
| Bluetooth Version | V2.1 + EDR (newer versions offer no benefits for headphones) |
| SBC codec | Customised SBC codec offers high fidelity without needing APT-X |
| Profile | Handsfree v1.6, Headset v1.1, A2DP v1.2 and AVRCP v1.4 |
| Effective Range | 10 meters (30 feet) |
| Working time | Music & calls up to 8 hours |
| Standby time | Up to 250 hours |
| Input voltage | DC 5V 100mA |
| Charging time | Approximately 2 hours |
| Dimensions | 23 x 13 mm earbud size, 540 mm cord length |
| Weight | Approx 13 g |
IN THE BOX
- BlueBuds X Bluetooth Headphones
- JayBird Carry Case
- 3 pairs eartips (S,M,L)
- 3 pairs ear cushions (S,M,L)
- 2 cord management clips
- USB Cable
- User Manual
CHARGING
Charging the battery before use is recommended but not required. BlueBuds X ships pre-charged however initial charge will vary.
Look for this Bluetooth headset battery status icon top right corner of your iPhone screen to see status of BlueBuds X battery.
PAIRING (SETTING UP) HEADPHONES WITH YOUR PHONE / MUSIC DEVICE
- With headphones turned off, & within 1 meter (3 feet) of music device, press & hold center key for more than 4 seconds until you see alternating red/green flashing of the status indicator and a voice prompt saying “Searching for your music device”.
- On your phone/music device, turn Bluetooth on & have it search for Bluetooth devices (see instructions in the phone/music device manual for details).
- Check for “BlueBuds X” and select (enter passcode 0000 if prompted).
- BlueBuds X voice prompt will say “headphones connected”.
- If the pairing is not successful, switch off headphones by pushing the center key for more than 4 seconds and repeat the steps outlined above.
PAIRING WITH A BLUETOOTH ADAPTER
- Place headphones and mobile phone within 1 meter (3 feet) of each other.
- Put the headphones into pair mode as outlined on prior page.
- If using BAU Universal Bluetooth Adapter put into pair mode also (see BAU manual).
- Plug the Bluetooth adapter into the music device and play a song.
- The headphones and adapter will pair automatically (passcode of adapter must be 0000).
- After successful pairing and connecting, the headphones will say “Headphones connected”
PAIRING WITH SEVERAL BLUETOOTH DEVICES
Paired devices will remember each other unless pairing information is deleted,
so there is no need to pair again. BlueBuds X can pair and remember 8 phone/music devices. Repeat the steps outlined on prior pages to set-up your headphones with another phone/music device. Note that if a 9th phone/music devices is paired the oldest pairing information is deleted. BlueBuds X will connect with the latest connected device. If you want to use another paired phone/music device, switch off the Bluetooth function of the current Bluetooth device, and then connect it with the other phone/music device by selecting “BlueBuds X” in the Bluetooth device list and press connect. Turn the originally paired device back on to reconnect and switch between either of the devices.
CONTROLS
BEGIN WITH THE TRADITIONAL UNDER-EAR FIT OPTION TO DETERMINE YOUR SIZES
- INSIDE THE ACCESSORIES PACKET
- L&R ORIENTATION
NOTE EARTIPS ANGLE INWARDS (FORWARDS) FOLLOWING DIRECTION OF YOUR EAR CANAL.
This means that L&R orientation is reversed for over-ear, as explained later.
WHEN WORN UNDER-EAR: CONTROLLER ON RIGHT side
3. GREAT SOUND PERFORMANCE IS IN SELECTING THE RIGHT SIZE EARTIP
WE LOVE GREAT SOUND. MAKE SURE YOU HEAR IT.
Because everyone’s ears are different, be sure to try all sizes of eartips. Only with the right size eartips will you enjoy a snug fit & premium sound quality.
BACK IT UP WITH SECURE FIT EAR CUSHIONS.
The earbuds may slip out of your ear a little. You will lose bass when this happens so use the secure fit ear cushions to hold them in place for best sound.
4. SOUND CHECK
Pair (set up) headphones to your music device, play music, and try each size of eartip to find the best fit and sound performance.
A proper seal is essential for you to fully appreciate the high quality audio of BlueBuds X.
NEED HELP PAIRING?
Full pairing details pages 29-32.
5. SECURE FIT
INSTALL YOUR PREFERRED SIZED SECURE FIT EAR CUSHIONS AS SHOWN.
FITTING / SIZE SELECTION GUIDANCE ON NEXT TWO PAGES.
- SLIDE SECURE FIT EAR CUSHIONS ALL THE WAY BACK AND COVER LED (DON’T WORRY, LED GLOWS CLEARLY THROUGH THE EAR CUSHION).
- LOCK THE TIP OF THE EAR CUSHION INTO THE TOP OF THE BOWL OF THE EAR AS SHOWN.
- YOU SHOULD HAVE A SNUG FIT WITH CONTACT ON THE LOWER, BACK AND TOP PORTIONS OF THE BOWL OF THE EAR.
6. ENJOY
ADVANCED OVER-EAR FIT OPTION
FURTHER TO THE MENTION ON THE BOX…
OVER-EAR FIT IS DEDICATED TO MUSIC, NOT DESIGNED FOR CALLS.
IT LIBERATES SPORTS MUSIC LISTENING BY LIFTING THE CORD OFF THE NECK, AND SHIFTS THE MIC BEHIND THE EAR.
SOME ADJUSTMENT TIME IS NEEDED WHEN SWITCHING BETWEEN FIT OPTIONS.
1. NOW THAT YOU KNOW YOUR PREFERRED EAR TIP & CUSHION…
and have a sense of the audio performance without other distractions, you are ready for over-ear fitting.
REMOVE THE SECURE FIT EAR CUSHIONS. YOU WILL INSTALL THEM DIFFERENTLY THIS TIME.
Your ear canal travels up and forward. The intelligent patent pending BlueBuds X angles to the same direction in either wearing style, encouraging a great, snug fit.
2. L&R ORIENTATION
NOTE EARTIPS ANGLE INWARDS (FORWARDS) & UPWARDS, FOLLOWING THE DIRECTION OF YOUR EAR CANAL.
WHEN WORN OVER-EAR: CONTROLLER ON LEFT side
3. SECURE FIT
TAKE YOUR PREFERRED SIZED SECURE FIT EAR CUSHION AND INSTALL IN REVERSE DIRECTION WITH POINTED END NEXT TO CORD.
IMPORTANT: Check your size preference in under-ear mode first as it can be difficult to tell in over-ear mode, and may be different to other JayBird products.
4. CORD MANAGEMENT CLIPS
Over-ear mode requires less cord, so before fitting, install the cord management clips to secure the slack for a customized fit.
- MAKE AN “S” SHAPE WITH THE MIDDLE SECTION OF THE CORD.
- INSERT CORD INTO 2 OF THE 3 SLOTS IN EACH CLIP AS SHOWN OMITTING THE FINAL ROUNDED SLOTS.
- – PUT THE HEADPHONES ON, USING INDEX FINGER TO PUSH TIP OF EAR CUSHION INTO PLACE TO SECURE EARBUDS (A MIRROR HELPS FIRST TIME).
- – WITH EARBUDS SECURED, ADJUST POSITION OF CORD MANAGERS (PULLING TOO TIGHT WILL OF COURSE DISLODGE EARBUDS, KEEP A LITTLE SLACK).
- TAKE OFF HEADPHONES, INSERT CORD INTO THE FINAL ROUNDED SLOTS, PUT HEADPHONES BACK ON, NOW YOU ARE READY TO GO!
5. ENJOY
Source
- jaybirdsport.com
- Download User Manual – Download
- Product Page – Click Here
Read More