Mee Audio T1CMA Headphones User Manual

Mee Audio T1CMA Headphones User Manual : In this user guide manual, we will unbox the Mee Audio T1CMA Headphones manual.

Mee Audio T1CMA Headphones User Manual

Mee Audio T1CMA Headphones User Manual
Mee Audio T1CMA Headphones User Manual

PACKAGE CONTENTS

  • CONNECT Bluetooth Transmitter
  • MATRIX CINEMA Bluetooth Stereo Headphones
  • 2 x Micro-USB power cables
  • Digital optical S/PDIF audio cable
  • 3.5mm audio cable
  • RCA audio cable

Getting Started

  • Plug the micro-USB power cable into the micro-USB POWER port of the Connect
  • Plug the USB end of the cable into an AC adapter, TV, or computer USB port.

CHARGE HEADPHONES

  • Plug the micro-USB power cable into the micro-USB power port of the Matrix Cinema.
  • Plug the USB end of the cable into an AC adapter, TV, or computer USB port.
  • Charge for 2 hour

Power on and Connect

The Connect transmitter and Matrix Cinema headphones are paired and ready to use and will connect automatically once powered on.

  1. Slide the ON/OFF switch of the Connect transmitter to the ON position.
  2. Slide the ON/OFF switch of the Matrix Cinema headphones to the ON position
  3. A solid blue light will appear on the transmitter to indicate that a connection is established

A SOLID BLUE LIGHT ON TRANSMITTER INDICATES CONNECTION

CHOICE A: OPTICAL

  • Remove protective caps from both ends of the digital optical S/PDIF audio cable
  • Plug digital optical S/PDIF audio cable into the OPTICAL audio input of the Connect
  • Plug the other end into the TV’s DIGITAL AUDIO OUT (OPTICAL) port.
  • Test for sound. Make sure the volume on both your TV and headphones is turned up.

NO SOUND? CHECK YOUR TV SETTINGS

  • Change Sound Output to “Optical”**
  • Change Digital Audio Output Format to “STEREO” or “PCM”**† – This may also need to done in the audio output settings menu(s) of your streaming app(s) and/or device(s) such as Apple TV®

**Exact menu and item names may vary between TVs. †On some TVs settings may be located in “Advanced settings” or “Expert settings” submenus

CHOICE B: 3.5 MM

  • Plug 3.5 mm audio cable into the 3.5 mm audio input of the Connect
  • Plug the other end into the TV’s headphone jack – Headphone jack may be located on rear, side, front, or bottom of TV
  • Test for sound. Make sure the volume on both your TV and headphones is turned up.

CHOICE C: RCA

  • Plug red/white ends of RCA audio cable into the TV’s red/white RCA AUDIO OUT port.
  • Plug 3.5 mm end of RCA audio cable into the 3.5 mm audio input of the Connect
  • Test for sound. Make sure the volume on both your TV and headphones is turned up.

NO SOUND? CHECK YOUR TV SETTINGS.

  • Change audio output settings to “VARIABLE”.
  • Set TV’s internal speakers to “OFF” – **Exact menu and item names may vary between TVs.

ADJUSTING VOLUME

Tap the Volume Up or Volume Down buttons on the Matrix Cinema to adjust headphone volume.

CHANGING AUDIO MODE

Tap the CinemaEAR button on the Matrix Cinema to enable CinemaEAR and to change the audio mode. There are four audio modes available.

Clear Voice Mode : Boosts speech clarity to make dialogue easier to hear over background sounds.

Clear Voice Plus Mode : Additional enhancement to provide a greater boost in speech clarity and intelligibility.

Dynamic Music Mode : Improves bass and treble response to make music sound more lively and exciting

Bass Boost Mode : Enhances bass response and depth to create more impact and immersion with movies and music

Hold the Cinema EAR button for 3 seconds to disable the Cinema EAR audio enhancement feature.

POWERING OFF

When finished listening, power off headphones until next use.

The Connect transmitter can be left powered on and plugged into USB power.

SUBSEQUENT USE

When ready to use again, simply power on the headphones and they will reconnect automatically.

Do not put the Connect or your headphones into pairing mode

A solid blue light on the Connect will indicate that a connection has been re-established.

Connect OVERVIEW

Mee Audio T1CMA Headphones Connect Overview
Mee Audio T1CMA Headphones Connect Overview

LED INDICATOR LIGHTS

The status of the Connect is shown by a green power / charging indicator light on the rear of the unit and two blue indicator lights on the top as follows :

INDICATOR LIGHT (S)CONNECT STATUS
USB Power plugged in,
green power indicator light solid
Battery full
USB Power plugged in,
green power indicator
light pulsing slowly
Charging
USB Power not plugged in,
green power indicator light solid
Powered on
USB Power not plugged in,
green power indicator
light blinking rapidly
Low battery
Blue light blinkingPairing mode active
One solid blue lightOne Bluetooth device is connected
Two solid blue lightsTwo Bluetooth
devices are connected

PAIR NEW/ADDITIONAL BLUETOOTH HEADPHONES

This procedure is used to re-pair the Matrix Cinema headphones if they do not reconnect automatically, to pair a different headphone with the Connect transmitter, or to pair a second headphone when one is already connected. Note: Turn off all nearby Bluetooth devices, including TVs, phones, tablets, computers, etc. before beginning the pairing process.

1. Put your Bluetooth headphones in pairing mode

Matrix Cinema headphones: Slide the ON/OFF switch to the ON position, then hold the Multifunction button for about 5 seconds until the status indicator light begins to flash red and blue and the headphone says “Ready to Pair”.

Other headphones: Consult the user manual of your Bluetooth headphones for the correct pairing procedure

2. Once the headphones are in pairing mode, click Pairing button “B” once to put the Connect in pairing mode.

Blinking blue light will change to solid blue light once successfully paired. If two headphones are paired, two solid blue lights will be shown.

PAIRING SIDE “B” BLINKING BLUE LIGHT – HEADPHONES PAIRED SOLID BLUE LIGHT

FACTORY RESET/CLEAR MEMORY

To perform a factory reset of the Connect, power on the Connect and hold Pairing button “A” for approximately 5 seconds until the blue indicator light stops blinking.

All previously paired devices will be cleared from memory and a new pairing will need to be created by following the pairing procedure above.

Matrix Cinema OVERVIEW

Mee Audio T1CMA Headphones Matrix Cinema Overview
Mee Audio T1CMA Headphones Matrix Cinema Overview
  1. 3.5 mm audio jack
  2. Charging Indicator light
  3. Micro-USB charging port
  4. Volume Up / Skip Track button
  5. Volume Down / Previous Track button
  6. Status Indicator light
  7. Multifunction button
  8. Power On/Off switch
  9. Microphone
  10. CinemaEAR button

CHARGING

The Matrix Cinema headphones should be charged roughly every 28 hours of use. Connect micro-USB cable to the charging port of the Matrix Cinema and a powered-on computer or USB charger. Charging time is 2 hours. The red charging indicator light will turn off once fully charged. Low battery is indicated by a flashing red status indicator light and “battery low” voice notification every five minutes.

PAIRING WITH OTHER DEVICES

The Matrix Cinema can be used as a headset when connected to phones and tablets. It will first need to be paired with each device.

To pair the Matrix Cinema with a new device, power it on and put it in pairing mode by holding the Power / Multifunction button for about 5 seconds until the status indicator light begins to flash red and blue in an alternating pattern and the headphone says “Ready to Pair”.

Open the Bluetooth menu on the device you wish to pair (usually located in Settings->Bluetooth). If needed, select “search for devices”, “add new device”, or “refresh.” Select “MEE audio Matrix Cinema” and allow pairing to complete.

It is only necessary to pair your headphones once with each new device.

CONTROLS WITH PHONES AND TABLETS

The headphone controls on the Matrix Cinema are located on the right earcup

Mee Audio T1CMA Headphones Control with phones and tablet
Mee Audio T1CMA Headphones Control with phones and tablet

*To start playing music, open a music app on your device and start playback. **Not all devices support this functionality. For more information, refer to the user manual for your device.

CHANGING AUDIO MODE

CinemaEAR is an advanced audio enhancement feature that allows for on-the-fly audio adjustment with four different hearing and sound enhancement modes:

Clear Voice Mode – Boosts speech clarity to make dialogue easier to hear over
background sounds

Clear Voice Plus Mode – Additional enhancement to provide a greater boost in speech clarity and intelligibility

Dynamic Music Mode – Improves bass and treble response to make music sound more lively and exciting

Bass Boost Mode – Enhances bass response and depth to create more impact and
immersion with movies and music

TAP] – Enable CinemaEAR (when disabled)
[TAP] – Next CinemaEAR mode
[HOLD 3 sec] – Disable CinemaEAR

CinemaEAR is disabled by default

DISABLING AUDIO PROMPTS

The Matrix Cinema’s voice prompts can be disabled for uninterrupted
listening

*Standby mode: headphones are powered on but not connected to any Bluetooth device(s). While in standby mode, the blue status indicator light blinks every second.

Mee Audio T1CMA Headphones DISABLING AUDIO PROMPTS
Mee Audio T1CMA Headphones DISABLING AUDIO PROMPTS

DISABLING STATUS INDICATOR LIGHT

The status indicator light on the right earcup of the Matrix Cinema can be disabled for uninterrupted use in low-light environments.

Disable Indicator Light: Press and hold Multifunction and Volume down buttons for 3 seconds

Enable Indicator Light: Press and hold Multifunction and Volume down buttons for 3 seconds

Note: the charging and low battery notification light on the left earcup cannot be disabled.

FACTORY RESET

This can be used to restore all of the features of the Matrix Cinema to their factory settings. Before the headphones can be used again, a new pairing will need to be created.

Press and hold the Multifunction and CinemaEAR buttons for 5 seconds.

Source

Read More

Leave a Comment