We have Skullcandy Grind True Wireless Earbuds Quick Start Guide in this post. Let’s unbox the manual of skullcandy Grind Earbuds manual.
Skullcandy Grind True Wireless Earbuds Quick Start Guide
Specifications
| Headphone Type | True Wireless In-Ear |
| Connection Type | Bluetooth 5.2 |
| Impedance | 22Ω±15% |
| Driver Diameter | 6mm |
| THD | <3% |
| Sound Pressure Level | 101+/-3dB |
| Frequency Response | 20Hz – 20KHz |
| Weight | 62.5g |
Let’s Gets Started
Take the earbuds out of the charging case and remove the protective stickers from the charging points.
- Place the earbuds in the charging case and leave the lid open. The LEDs will illuminate.
- Open Bluetooth setting on your device. Select Grind fuel from the list of available devices.
- Accept any Pair or Ok prompts. Your earbuds will connect to your devices. They are now ready to use.
Controls
Tip: Download the Skullcandy App for easy, always-on access to this list and additional features.
Button Controls
Power On/Off
- Remove the earbuds from the case to power On and connect.
- Place the earbuds in the case and close the lid to power the earbuds Off and charge.
Press 1 Time
| Play/Pause | Either Earbud |
| Answer/End Call | Either Earbud |
Press 2 Time
| Volume Up | Right Earbud |
| Volume Down | Left Earbud |
Press and Hold
To Launch and Play Spotify
| 1 Seconds | Play Audio | Left Earbud |
Share Audio Between Two Skullcandy Skull-iQ Enabled Products
| 3 Seconds | Share Audio | Right Earbud |
| 3 Seconds | Join Audio | Left Earbud |
Press Once, Release. Press Again & Hold
| 1 Seconds | Pair New Device | Either Earbud |
INITIAL SET UP & PAIRING HELP
Quick Start Version: (Easiest 1st time pairing, earbuds remain in case)
- To pair to your device for the first time, remove the stickers covering the charging points on both earbuds, place them into the charging case, make sure both LEDs show red, and leave the lid open.
- Both buds will then automatically power on and enter Pairing Mode while still in the case.
- Simply, turn on your device’s Bluetooth and look for GRIND FUEL* in your list of available Bluetooth devices.
- Select GRIND FUEL and accept the “Pair” or “OK” prompt that appears on your screen. When pairing is complete, a voice prompt will say “connected.”
1st Time Pairing after unboxing when removing earbuds from the case:
- To pair to your device for the first time, remove the stickers covering the charging points on both earbuds, place them into the charging case, make sure both LEDs show red, and close the lid for 5 seconds.
- Open the case lid and remove your earbuds.
- You’ll first hear the Power ON tone, followed by the battery capacity voice prompt “Battery …%”. Then you will hear the voice prompt “Ready to Pair” while BOTH the LEFT and RIGHT earbud will begin to pulse red and blue to indicate you are now in Pairing Mode.
- Now, turn on your device’s Bluetooth and look for GRIND FUEL in your list of available Bluetooth devices.
- Select GRIND FUEL and accept the “Pair” or “OK” prompt that appears on your screen. When pairing is complete, a voice prompt will say “connected.”
Pair to a new device: (after 1st time pairing, while earbuds are connected)
- To pair to a new device while you are currently Powered On and connected to a device, simply press EITHER earbud button 1x and then press and hold the same button 1 second. This will enter both earbuds into Pairing Mode.
- The voice prompt will say “Ready to Pair”, both earbuds will pulse red/blue, and you can select “GRIND FUEL ” from the new available Bluetooth device list. Please remember to accept the prompt that will appear on your screen.
Pair to a new device: (after 1st time pairing, while earbuds are non-connected)
- To pair to a new device, Power On both earbuds and simply disconnect the Bluetooth from the previously paired device so your earbuds are in a non-connected state. This will automatically enter both earbuds into Pairing Mode.
- The voice prompt will say “Ready to Pair”, both earbuds will pulse red/blue, and you can select “GRIND FUEL” from the new available Bluetooth device list. Please remember to accept the prompt that will appear on your screen.
QUICK START DEFAULT USER CONTROLA
Out of the box, GRIND FUEL’s default media controls are ready to keep you connected and in control of your Bluetooth enabled device.
We’ve also incorporated a simple feature that allows the user to hear each time they have pressed the button on their earbud, and when pressing more than one time in sequence, you will hear ascending tones to give you better control of your media. They are very subtle and do not disrupt your listening, easy to hear even while playing music, and the button response tone will help you quickly learn your way around the controls on your device.
Auto Power On & Power Off:
- When your earbuds are in the charge case, open the lid to Auto Power On your earbuds.
- While the earbuds are still in the case, the LED’s will turn BLUE if they are fully charged, and RED if they are still charging.
- Remove them from the case and you will hear the Power On “pling” Tone, battery life voice prompt, and the “connected” and “Voice Control On” Voice prompts if you had previously paired and linked with the Skullcandy APP.
- Place both earbuds back into the case, and CLOSE THE LID to power off and begin charging.
Manually Power On: Either
- 1 second hold
Manually Power Off: Either
- 2x press, then 1 second hold
- Action – Press, Press, Press and Hold 1s
Play/Pause: Either
- 1x press
Answer/Hang Up Call: Either
- 1x press
Reject incoming Call: Either
- 1x press
Volume Up: Right Bud
- 2x press
- Action – Press
Volume Down: Left Bud
- 2x press
- Action – Press
SHARE AUDIO:
Easily share your music or media with a friend, anytime and anywhere through our new Share Audio feature.
To Share Audio, both users must have SKULLiQ enabled products, be in Stereo Mode (using both earbuds), and be within Bluetooth range. For best results, we recommend both users stay within 5 meters (about 15 feet) during an Audio Share session. Please also note the audio share between users may take up to 5 seconds to sync.
The person that wants to share their audio must have their earbuds connected to a device. They will press and hold the button on their RIGHT earbud for 3 seconds. A voice prompt will notify the user that they are now “Sharing Audio”. Only the user sharing audio will still maintain their ability to utilize their Hands-Free Voice Control functionality and track controls.
The person that wants to join will press the button on their LEFT earbud for 3 seconds, and they can be in either a connected or non-connected state. A voice prompt will notify the user they are now “Joining Audio”. Once connected, the user joining will not have voice control or track control functionality.
Once the share is complete, audio will begin to stream automatically and each user will have the ability to adjust their volume independently through their earbuds.
Either party can disconnect from the Audio Share by placing their earbuds into the case and closing the lid, powering the earbud off manually, or repeating the 3-second hold you used to share or join the stream.
To continue the Share session if either user is disconnected, both parties will need to start over.
- Press and hold 3s on the right earbud to “Share” your audio (must be connected)
- Press and hold 3s on the left earbud to “Join” audio (can be connected or in a disconnected state)
Commands:
- Play (Music Streaming)
- Pause (Music Streaming)
- Volume Up (Music Streaming)
- Volume Down (Music Streaming)
- Next (Media Control)
- Previous (Media Control)
- Stay Aware On
- Stay Aware Off
- Spotify
- Assistant
Incoming Call:
- Accept (doesn’t require Wake Word)
- Reject (doesn’t require Wake Word)
Custom button functions during idle or streaming media:
Here are the controls that you can assign to the above button actions.
- Take Photo
- Next Track
- Previous Track
- Volume Up
- Volume Down
- Activate Phone Voice Assistant
- Spotify Tap
- Stay Aware Mode ON/OFF
How to Charge Skullcandy Earbuds
When fully charged, there will be up to 9+ hours of playtime in the buds and you will get 31+ hours in the charging case, reaching up to 40+ total hours of playtime.
EARBUDS:
- Place them in the case and CLOSE THE LID to begin charging.
- When you open the charging case, the LED’s on both earbuds will indicate if they are fully charged (solid BLUE) or if they are still charging (RED).
- 10 minutes of charging will provide 2+ hours of playtime.You will hear the “Battery Low” voice prompt with about 45 minutes of playtime remaining (about 15% charge), and again with about 20 minutes (8%) of playtime left.
- You can also check their battery life on the paired device on your shortcuts screen, or in the Skullcandy APP (earbud battery life shown individually) when they’re connected to your device.
CASE:
- Plug in the USB-C Rapid Charge cable and connect to a computer, wall charger, power bank or 12-volt adapter in a car. The white LED indicator above the USB-C port will pulse WHITE while charging, and will remain ON when the case has become fully charged.
- A 10-minute charge of the charging case via your USB-C cable will provide 4+ hours of battery play time.
- To check how much battery life is left, open the case lid and the case LED’s will turn on. Each LED represents 25% charge capacity, and while charging they will go from pulsing until all four LED’s are solid, which means your case is 100% charged.
Source
- Skullcandy.in
- Quick Start guide – Check here
- Product Page – Click Here
Read More