Soundcore Life P3 Noise Cancelling Earbuds User Manual

This is all about Soundcore Life P3 Noise Cancelling Earbuds User Manual in this user manual guide. Let’s check this.

Soundcore Life P3 Noise Cancelling Earbuds User Manual

Soundcore Life P3 Noise Cancelling Earbuds User Manual
Soundcore Life P3 Noise Cancelling Earbuds User Manual

Specifications

Input5V ⎓ 0.35A
Battery capacity63 mAh x 2 (earbuds); 800 mAh (charging case)
Charging time3 hours
Playtime (varies by volume level and content)Up to 7 hours (Total 35 hours with the charging case)
Playtime (with ANC mode turned on)Up to 6 hours (Total 30 hours with the charging case)
Driver size11 mm x 2
Frequency response20 Hz – 20 kHz
Impedance16 Ω
Waterproof levelIPX5
Bluetooth versionV 5.0
Bluetooth range15 m / 49 ft

Charging

  • Fully dry off the earbuds and the USB port before charging.
  • Use a certified USB-C charging cable and charger to prevent any damage.
  • Fully charge both the earbuds and the charging case before the first use.
  1. Place the earbuds in the charging case and close it.
  2. Connect the charging case to the power supply by using a USB-C charging cable. Alternatively, position the charging case at the center of your wireless charger for wireless charging.
  • The LED indicators on the charging case indicate the charging status.

Wearing

  1. Choose the EarTips that fit your ears best.
  2. Insert the earbuds into the inner canal of your ears and turn gently until you find the most comfortable and secure position.
Soundcore Life P3 Noise Cancelling Earbuds Wearing
Soundcore Life P3 Noise Cancelling Earbuds Wearing
  • Your earbuds come with multiple pairs of EarTips, among which Medium-sized are pre-installed.

Powering On/Off

  • Open the charging case, the earbuds will automatically power on.
  • To power off, place the earbuds in the charging case and close it.
Soundcore Life P3 Noise Cancelling Earbuds Powering On, Off
Soundcore Life P3 Noise Cancelling Earbuds Powering On, Off
  • The earbuds will automatically power off after 30 minutes if no device is connected.

Bluetooth Pairing

  1. Open the charging case, the earbuds will automatically enter the Bluetooth pairing mode.
  • The 3 LED indicators on the charging case will flash white in sequence continuously.

2. Select “Soundcore Life P3” on your device’s Bluetooth list to connect. When successfully connected, the LED indicators on the charging case will turn white for 3 seconds.

  • Pairing with another device: Place the earbuds in the charging case and leave the case open. To enter pairing mode, press and hold the button on the case for

3. seconds until the 3 LED indicators flash white in sequence continuously.

  • Each time you power on your Soundcore earbuds, they will automatically connect to your last successfully connected device if available within the Bluetooth range
  • Mono mode: When Bluetooth connected, you can use either one of the earbuds only by placing the other one into the charging case.
  • When powered on and connected, if either one of the earbuds is out of battery and powered off, you can keep using the other one.
  • When you are on a call, place either one of the earbuds into the charging case, and the microphone in the other earbud will be activated.

Controls

Music

Play/PausePress twice (R)
Next trackPress twice (L)
Switch ambient sound modes (Noise Cancellation/Normal)Press and hold for 2 seconds (L/R)

Calls

Answer a call
Answer a second incoming call and put the current call on hold
Press twice (L/R)
End/Reject a call
Switch between a call on hold and an active call
Press and hold for 2 seconds (L/R)

Mono mode

Play/PausePress twice
Answer a callPress twice
End/Reject a callPress and hold for 2 seconds
Activate Siri or other voice assistant softwarePress and hold for 2 seconds

Soundcore App

Download the Soundcore app to enhance your experience.

User interface customization: In stereo mode, all of the controls (e.g. adjust volume, control playback, activate Siri) can be customized in the app.

EQ settings: There are more than 20 EQ settings you can choose from in the app to optimize your experience while enjoying different music genres.

Noise cancellation: Choose an active noise cancellation mode to reduce ambient noise according to your surroundings.

  • Transport: Targets low-end frequencies like engine and road noise for peaceful journeys and commutes.
  • Outdoor: Reduces ambient sounds in cities for less distractions.
  • Indoor: Reduces voices and mid-frequency noise from coffee shops and other inside spaces.

Earbuds firmware upgrade: You will be informed once the new version of firmware is detected when you connect the earbuds with the app. Ensure the earbuds are placed in the charging case and the case remains open until the firmware upgrade is completed. During the upgrade, ensure the earbuds are being charged and avoid any operation.

Reset

You might need to reset the earbuds if you experience any connectivity problems or function issues.

  1. Place the earbuds in the charging case and leave the case open.
  2. Press and hold the button on the case for 10 seconds until the 3 LED indicators flash white for 3 times and then flash white in sequence continuously. This confirms that the reset was successful and your earbuds can be connected normally.
Soundcore Life P3 Noise Cancelling Earbuds Reset
Soundcore Life P3 Noise Cancelling Earbuds Reset

A Splash Of Sound

Thumping Beats

Life P3 noise cancelling earbuds have 11mm drivers and our exclusive BassUp technology to fuel rich sound with a thumping low end.

Multi-Mode Noise Cancelling

Target ambient noises indoors, outdoors, and while traveling on the train, subway, or bus for a distraction-free listening experience. Switch between modes depending on where you’re listening via the Soundcore app.

Multi-Mode Noise Cancelling

Target ambient noises indoors, outdoors, and while traveling on the train, subway, or bus for a distraction-free listening experience. Switch between modes depending on where you’re listening via the Soundcore app.

At the Center of the Action

Activate Gaming mode via the Soundcore app for a more immersive audio experience while playing your favorite mobile games.

 No Wires

For extra convenience, recharge Life P3’s charging case on a wireless charger. 

All-Day Listening

Life P3 noise cancelling earbuds have 7 hours of playtime from a single charge which extends to 35 hours with the compact charging case. 

Customize Your Listening

The Soundcore app allows you to customize everything from the EQ to creating your own relaxing white noise soundscape. Also, test the earbuds’ fit, update firmware, and more.

Find Your Earbuds 

Go to the Soundcore app and activate “Find My Headset”. The lost earbud will emit a loud noise to help you locate it.

Secure and Comfortable

Built to hug the curve of your ear, Life P3 noise cancelling earbuds sit stably in your ear. Mix and match the various sizes of eartips for the best fit and seal.

FAQ

Bluetooth

How do I reset Life P3?

  1. Place the earbuds into the charging case and keep the case open.
  2. Press and hold the button on the charging case for 10 seconds until 3 LED indicators on the charging case flash white 3 times and then flash white in sequence continuously. This confirms that the reset is successful.

When resetting the earbuds, make sure the earbuds are well connected with the case, or it may cause resetting failure. The first and third LEDs will flash to indicate that they are properly connected. (When earbuds are placed in the charging case, the first LED flashes twice when the left earbud is in the case, and the third LED flashes twice when the right earbud is in the case).

What should I do if any of the following problems occur?

  1. Cannot pair or reconnect with my device.
  2. One side does not pair with the other side or my device.
  3. No music plays after connecting with my device.
  4. Only one earbud has sound.
  1. Remove the protective film covering the connectors on the earbuds.
  2. Reboot the Bluetooth device, such as a phone or computer. Forget all the pairing records on your device and turn off Bluetooth.
  3. Reset the earbuds as per the steps below (make sure your earbuds have enough battery). *Place the earbuds into the charging case and keep the case open. *Press and hold the button on the charging case for 10 seconds until 3 LED indicators on the charging case flash white 3 times and then flash white in sequence continuously. This confirms that the reset is successful.

When resetting the earbuds, make sure the earbuds are well connected with the case, or it may cause resetting failure. The first and third LEDs will flash to indicate that they are properly connected. (The first LED flashes twice when the left earbud is in the case, and the third LED flashes twice when the right earbud is in the case).

4. Turn on the Bluetooth of your device and search for Soundcore Life P3 and pair.

If there is a pop-up window to confirm pairing for “Soundcore Life P3,” please select “pair.” If you accidentally select “cancel,” you need to refresh (turn off and turn on) the Bluetooth of your device and pair the earbuds again.

What should I do if Life P3 disconnects or the sound is choppy?

Please note that this doesn’t necessarily mean there is an issue with the earbuds but may have something to do with the connected device and environment. Bluetooth signals may be influenced by obstructions, such as walls, pillars, home appliances, Wi-Fi, and more. To ensure a stable connection, we recommend avoiding such obstructions.

To fix this issue, please try the following:

  1. Fully charge and reset your earbuds as stated below and re-pair them.
  • *Place the earbuds into the charging case and keep the case open.
  • *Press and hold the button on the charging case for 10 seconds until 3 LED indicators on the charging case flash white 3 times and then flash white in sequence continuously. This confirms that the reset was successful.

2. Check the earbuds by listening to a downloaded music/video.
3. Check the earbuds with another Bluetooth device in a different environment to see if it works well.

Bluetooth related issue (cannot be paired / disconnected) when connected to a computer

1. Fully charge and reset your earbuds as stated below:

  • *Place the earbuds into the charging case and keep the case open.
  • *Press and hold the button on the charging case for 10 seconds until 3 LED indicators on the charging case flash white 3 times and then flash white in sequence continuously. This confirms that the reset was successful.

2. Upgrade your computer’s Bluetooth driver to the latest version.
3. Re-pair your earbuds to your computer.
4. Test the earbuds on your phone to see if they are working properly.

App

Cannot find Life P3 on the Soundcore App?

  1. Pair your earbuds with your phone. Currently, the Soundcore App does not support computers.
  2. Click on the Soundcore App, and choose Headphones> Life >Life P3 to connect the earbuds.
  3. If you cannot find Life P3 in the list, please update the app to the latest version (the version should be above 2.7.0.).
  4. Uninstall then proceed to reinstall the Soundcore App.

If the problem still persists, please let us know the version of your Soundcore App and the phone model used so we can assist you better.

Sound

1. Make sure your earbuds have enough power before resetting them:

  • *Place the earbuds into the charging case and keep the case open.
  • *Press and hold the button on the charging case for 10 seconds until 3 LED indicators on the charging case flash white 3 times and then flash white in sequence continuously. This confirms that the reset was successful.

2. Clear all the pairing records on your phone and re-pair your earbuds. Turn the volume down one notch on your phone. Then turn up the volume of both your phone and earbuds with the music/video to the maximum.
3. Use a Q-tip with a bit of rubbing alcohol to gently clean the metal mesh filter under the rubber ear tips.

Low volume when connected to a Mac computer?

1. Make sure your earbuds have enough power before resetting them;

  • *Place the earbuds into the charging case and keep the case open. *Press and hold the button on the charging case for 10 seconds until 3 LED indicators on the charging case flash white 3 times and then flash white in sequence continuously. This confirms that the reset was successful.

2. Clear all the pairing records on your Mac computer and re-pair your earbuds. Turn the volume down one notch on your Mac computer. Then turn up the volume of both your Mac computer and earbuds with the music/video to the maximum.
3. Use a Q-tip with a bit of rubbing alcohol to gently clean the metal mesh filter under the rubber ear tips.

Low volume when connected to a Windows computer?

1. Make sure your earbuds have enough power before resetting them:

  • *Place the earbuds into the charging case and keep the case open.
  • *Press and hold the button on the charging case for 10 seconds until 3 LED indicators on the charging case flash white 3 times and then flash white in sequence continuously. This confirms that the reset was successful.

2. Clear all the pairing records on your Windows computer and re-pair your earbuds. Make sure you choose the right mode (For audio/video, choose Stereo, and for mic choose Hands-Free)
3. Turn up the volume of your computer, earbuds and music/video to the maximum.
4. Use a Q-tip with a bit of rubbing alcohol to gently clean the metal mesh filter under the rubber ear tips.

Setting the input and output on a Windows computer with Life P3?

  1. If you only want to listen to the audio on the computer, select “Life P3 Stereo” for the computer audio. If you need to adjust the volume, adjust both the software and the computer volume.
  2. If you need to use a conference app on your computer such as Zoom/Microsoft Teams, please set the input and output of the software as stated below:
  • Microphone on the conference software: Life P3 Hands-Free
  • Speaker on the conference app: Life P3 Hands-Free

If you need to adjust the volume, please do so on the app. If you cannot adjust the volume on the app, please select the Life P3 Hands-Free as output on your computer and adjust the volume.

3. If you need to use an audio and video app on the computer and you cannot set the input and output on the app, please open the computer audio settings and choose the correct settings:

  • Input: Life P3 Hands-Free
  • Output: Life P3 Hands-Free

Charging

How long does it take to fully charge the earbuds?

About 2 hours.

How long does it take to fully charge the charging case?

About 3 hours.

Does the case support wireless charging?

Yes, place the case on a wireless charging pad and make sure it’s closed and centrally aligned. If it starts charging you will see the LEDs blinking.

How can I charge the earbuds?

  1.  Confirm that the charging case has power left (open the lid of the charging case to check if there is any indication on the LED).
  2. Close the lid after placing the earbuds in the charging case and start charging.

What should I do if any of the following problems occur?

  1. The earbuds don’t recharge in the charging case.
  2. The earbuds stay connected to the device even after being placed in the charging case with the lid closed.
  3. The earbuds don’t turn on when taken out of the charging case.
  1. Confirm the charging case has power left (open the charging case lid to check if there is any indication on the LED).
  2. Clean the charging pins with a dry cloth and an alcohol-based disinfectant. This is to ensure all charging contact pins on the earbuds and charging case are completely clean and dry of sweat and water. Then put the earbuds correctly into the case. When you put the earbuds back into the charging case, the first and third lights on the case will flash twice to indicate both earbuds are charging normally.
  3. If they still do not turn on, put the earbuds back into the charging case and close the lid for 6 seconds, and try opening the lid again.

Source

Read More

Leave a Comment