In this user manual guide, we will review the Soundcore Life P2 Wireless Earbuds User Manual. Let’s check this.
Soundcore Life P2 Wireless Earbuds User Manual
Specifications
| Input | 5 V 500 mA |
| Rated output power | 7 mW @ 1% THD |
| Battery capacity | 55 mA x 2 (earbuds); 700 mA (charging case) |
| Charging time | 2 hours |
| Playtime (varies by volume level and content) | 7 hours (Totally 40 hours with the charging case) |
| Driver size | 6 mm × 2 |
| Frequency response | 20 Hz – 20 kHz |
| Impedance | 16 Ω |
| Bluetooth version | V 5.0 |
| Bluetooth range | 10 m / 33 ft |
Qualcomm aptX Technical specifications
- Compression ratio: 4:1
- Word depth: Support 16bit and 24bit
- Decoding delay: Sample rate 48kHz<2ms
- Dynamic range: 16bit>92dB, 24bit>120dB
- Data rates: 352kbps
- Decode mode: Stereo
Charging
- Remove the protective film from the earbuds when using for the first time.
- Fully charge both the earbuds and the charging case before the first use.
- To prevent damage, use the provided USB-C cable.
- Fully dry off the earbuds and the USB port before charging.
LED indicators (Earbuds & Charging case)
| Steady white | Being Charging |
| Light off | Fully charged Remaining battery >10% (when in use) |
Powering On/Off
The earbuds will automatically power on when taken out of the charging case and power off when placed back into the charging case.
LED indicators (Earbuds)
| ON | Steady white for 1 second |
| OFF | Steady red for 1 second |
- To manually power on, press the multi-function button on either one of the earbuds.
- To manually power off, press and hold the multi-function button on either one of the earbuds for 3 seconds.
Pairing
- True Wireless Stereo Connection
- The right earbud will automatically connect with the left earbud when taken out of the charging case.
LED indicators (Earbuds)
| Breathing white | TWS connecting |
| Steady white for 1 second | TWS connected |
- When powered off, press and hold the multi-function button on both earbuds for 1 second, the earbuds will enter TWS connecting mode.
- When powered on and connected, place either one of the earbuds into the charging case, you can keep using the other one.
- When powered on and connected, if either one of the earbuds is out of battery and powered off, you can keep using the other one.
When you are on a call, place either one of the earbuds into the charging case, 3 to 5 seconds later, the microphone in the other earbud will be activated.
Bluetooth Pairing with your Device
The earbuds will enter pairing mode when powered on. You are requested to confirm the connection when you see a pop-up.
LED indicators (Earbuds)
| Flashing white | Bluetooth pairing |
| Steady white for 1 second | Bluetooth connected |
In the pairing process, some devices are incompatible with Qualcomm True Wireless Primary- Secondary dual pairing names, it may notice “connection unsuccessful” when you tap “Pair” or even no screen pops up. Don’t worry and it will not influence the using.
Once successfully paired, the primary earbud connects with your device and transfers signal to the secondary earbud, the latter one will not connect with your device. As a result, in the Bluetooth pairing list on your device, it may indicate that only one side is connected while the other side is not.
- To pair with another Bluetooth device, turn off Bluetooth on the currently connected device first.
- Each time you power on your Soundcore earphones, it will automatically connect to your last successfully connected device if available within the Bluetooth range.
Wearing
- Choose the EarTips that fit your ears best.
- Insert the earbuds into the inner canal of your ears.
- Turn and find the most comfortable position.
Controls
Music
| Press (R/L)Play / Pause | Press (R/L) |
| Next track | Press twice (R) |
| Previous track | Press twice (L) |
| Volume up / down | Control volume via the connected device |
Calls
| Answer / End a call | Press (R/L) |
| Reject a call | Press and hold for 1 second (R/L) |
| Enable mono mode | Remove either one of the earbuds off your ear and press and hold the button on the other earbud for 1 second |
Mice
| Activate Siri or other voice assistant software | Press and hold for 1 second (R/L) |
Reset
Reset the earbuds if the earbuds cannot connect with each other properly or cannot connect with your device properly.
- Place the earbuds into the charging case and make sure they are being charged.
- Press and hold the button on both earbuds for 3 seconds until the LED indicators flash red 3 times and then turn white.
All the memory data will be cleared.
Graphene Enhanced Sound, Crystal Clear Calls
Wider Soundstage
Life P2’s graphene drivers oscillate with extreme precision to bring you sound with extraordinary accuracy and an ultra-realistic listening experience.
Incredible Call Quality
Utilizing the latest cVc noise reduction technology and 4 microphones (2 per earbud), Life P2 wireless earbuds enhance voice pick up and remove background noises-Ideal for home offices.
On-The-Go Listening
Enjoy 7 hours of listening from a single charge, and extend it to 40 hours with the compact charging case. For a quick boost of power when you’re on the move, charge the earbuds for just 10 minutes and get 1 hour of listening.
Seriously Strong Connection
Bluetooth 5.0 creates an unbreakable connection between your device and Life P2 wireless earbuds for skip-free audio even in busy spaces.
Simple Secure Fit
Get a confident and satisfying fit in only 3 steps. For the best call quality, ensure the microphone is directed towards your mouth.
IPX7 Waterproof
Protection against liquids such as rain, sweat, and water.
Product/Features
| Sound | Premium sound via diamond-inspired drivers |
| Calls | 4 microphones |
| Playtime Per Charge | 7 Hours |
| Total Playtime with Charging Case | 40 Hours |
| Fast Charging | Charge for 10 minutes, Listen for 1 hour |
| Bluetooth | Bluetooth 5 |
| Single Use | Both earbuds |
| Other Features | Single earbud use, USB-C, PUSH AND GO technology |
| Recommended For | Business calls, commute, travel，sports |
FAQ
How long will it take to charge Life P2?
About 2 hours.
After exercise, wipe the charging port dry with a cotton cloth to ensure there’s no sweat on the port before charging.
What should I do if the earbuds don’t turn on or charge?
- Make sure the protective film below the earbud has been removed.
- Try another charging cable and wall charger to charge the case with the earbuds in it. There will be one steady white light on the case while it’s charging and a steady white light on each earbud to indicate the earbuds are charging in the case. The light will turn off when they are fully charged.
- Clean the charging pin with a dry cloth, then put the earbuds into the charging case, and charge the case and earbuds with the charging cable at least for 10 minutes.
Why doesn’t the light on the charging case light up?
The light on the charging case only lights up when it has less than 10% battery life (red indicator) or when the case is charging (white indicator).
Does Life P2 support wireless charging?
No.
Bluetooth
How do I reset Life P2?
- Place the earbuds into the charging case and make sure they are being charged.
- Press and hold the button on both earbuds for 3 seconds. The LED indicators will flash red 3 times and then turn white.
What should I do if the earbuds don’t pair with my device?
- Ensure your device’s Bluetooth setting is enabled and your device is within 1 m (3 ft).
- Clear the Bluetooth connection record on your phone and re-pair.
- Reset your earbuds. See “How do I reset Life P2?”
- Try to pair with another device.
What should I do if Life P2 disconnects from my device?
- Reset the earbuds. See “How do I reset Life P2?”.
- While the range of most Bluetooth devices is 33 feet (10 meters), the optimal range for any Bluetooth audio device is about 2 feet (60 centimeters) from the audio source.
- Some environments (such as airports, offices, crowded public spaces etc.), other Bluetooth connections, and Wi-Fi can interfere with your Bluetooth connection. Optimizing your Bluetooth connection:
- If you are in a busy place, ensure your phone is on your right side when using Life P2.
- Download videos and songs instead of streaming.
- If you have an Android phone, temporarily disable unnecessary apps running in the background.
- Stay away from Wi-Fi transmitters.
What should I do if the secondary earbud doesn’t connect with my device when the primary earbud is turned off?
- Normally, when the primary earbud is turned off you’ll need to wait 3-4 second for the secondary earbud to automatically connect to your device.
- If it doesn’t connect, you can manually connect by clicking on the secondary earbud’s Bluetooth name in your phone’s Bluetooth list.
- If this doesn’t work, reset the earphones. See “How do I reset Life P2?”.
Can Life P2 be pair with multiple devices at the same time?
This feature is currently not supported.
If you want to pair Life P2 with a second device, please use one of the following methods:
- Turn off Bluetooth on the currently connected device and then connect another Bluetooth device.
- Hold down the button on either earbud for 3 seconds to turn if off first, and then turn on Bluetooth on another device and hold the button on either earbud until you see the white light flashing quickly.
Waterproof
Is the charging case waterproof?
No, the case is not waterproof. Wipe the earbuds dry with a dry, lint-free cloth after workouts, heavy sweating, or getting splashed with water. Ensure the earbuds are completely dry before placing them in the charging case.
What’s the waterproof rating of the earbuds?
The earbuds have an IPX7 Waterproof rating under IEC standard 60529, which means they are designed to handle rain and workout conditions. The earbuds are not designed for swimming, showering, or exposure to pool or ocean water. Do not wear the earbuds in a sauna or steam room.
Note: The waterproof function’s effectiveness may reduce over time as a result of daily use.
Sound
What Bluetooth codecs are supported?
Life P2 supports aptX, SBC, and AAC.
How do I switch between stereo and mono mode?
When you use Life P2 for the first time the right side is the primary earbud and the left is the secondary by default. Wait for Soundcore Life P2-L (or headset on some devices) pairing request and click “pair”. If you click “cancel” this will not affect your use of the earbuds in stereo mode, but will affect your ability to switch between stereo and mono mode.
Ways to Switch:
- Place either one of the earbuds in the charging case or hold down the button on one earbud to turn it off manually, you can keep using the other one.
- If either one of the earbuds is out of battery and powered off, you can keep using the other one.
Notes:
- For iPhone 11 Series: Manually switch between the primary and secondary earbuds by clicking on the Bluetooth name of the secondary earbud on your device.
- When you switch from stereo to mono, the audio will pause. Within 2-4 seconds Life P2 will connect again so press play to continue listening.
- If switching to mono mode fails, clear Life P2 from your phone’s Bluetooth connection record and pair again.
Can I use my earbuds in mono mode?
- Yes, simply remove one earbud from the charging case while the other is charging.
- If the earbud has not previously been connected to your device, manually click the earbud’s Bluetooth name on your device to pair it to use.
What should I do if only one earbud works or no music plays from both earbuds while connected?
- Place both earbuds back in the charging case and close it, then take them both out at the same time and try again.
- If this doesn’t work, reset your earbuds. Follow the steps below:
- Forget the pairing records (both Soundcore Life P2 and Soundcore Life P2 L) on your device and turn off Bluetooth.
- Place the earbuds into the charging case and make sure they are being charged.
- Press and hold the button on both earbuds for 3 seconds. The LED indicators will flash red 3 times and then turn white.
- After resetting, take both earbuds out of the charging case to make sure they have paired successfully. If the pairing is successful, you will see a white light flashing quickly on one earbud and a white light flashing slowly on the other.
- Turn on Bluetooth again and search for Soundcore Life P2 (not Soundcore Life P2 L) and pair.
What should I do if the other side can’t hear me after I remove one of the earbuds during a phone call?
Only one headset microphone works during the call. If you want to switch from stereo to mono call, press and hold the button on the earbud in your ear for one second while removing the other earbud.
Why is there no sound playing when Life P2 are connected to my PC via Bluetooth?
- Delete the pairing record and reconnect Life P2 again.
- You may need to change the default audio output on your PC to “Bluetooth Headset”.
- Update your computer’s Bluetooth driver or buy a Bluetooth adapter that is compatible with your computer.
Source
- soundcore.com
- Download User Manual – Download
- Product Page – Click Here
Read More